Product Description
GATE MOSFET WARFET AEG control system
-MOSFET (FET function) (FET function: does not burn the switch) Uses the latest ultra-small FET that is resistant to heat
-Precoque (Piston in standby position in the retracted position, like a real gun for firing feeling!)
-Active brake (ON / OFF) (stops the motor quickly and dramatically improves the sharpness of the cicada
-Smart fuse (protects the board from overheating, overcurrent and overvoltage)
-Built-in self-test function (automatically checks if the FET is operating normally)
-Battery protection function (Prevents excessive discharge of Lipo battery: LiPo 7.4V, 11.1V, 14.8V only)
-The industry's first tactical programming card allows you to see the control unit settings at a glance!
-Current sensor * Compact and rugged control unit for electric gun ・ Operation test with 12V battery for automobile.
-Tamiya-type connector can be attached to many electric gun batteries.
-By installing using the signal line double, the power lost in the switch part is cut, and the power from the battery to the motor is directly transmitted.
-Overdischarge prevention function: 7.4V, 11.1V, 14.8V LiPoly, 9.6V, 12.8V LiFePO4-Extends battery life, increases rotation speed, and improves gearbox reliability. (Except when pre-cock is set) Other than that, it was born with the function of Morimori! With WARFET, no other FET is needed!
-Compatible models: As long as space can be secured, it can be used for Tokyo Marui and almost all electric guns.
-Size Power module (MOSFET body) Size: 56x20x9mm (nominal value) Weight: 9.4g (nominal value) Tactical programming card (setting card) Size: 67x53x7mm (nominal value) Weight: 27.3g (nominal value)
-Accessories (per pc): Power module x 1 Tactical programming card x 1 Signal line Single x 1 Double x 1 T connector x 1 set Tamiya-type connector adapter Male and female x 1 <Note: Before purchase Please check>
※Do not bring the programming card or control unit close to a motor or strong magnetic force, or it will break. (Destruction caused by magnetic force is not covered by the warranty)
※Use a battery with a fully charged battery voltage of 17V or less.
※Nickad, Lipo battery (Lipo) referrer and NiMH battery are supported, but over discharge prevention program is only compatible with Lipo battery 7.4V, 11.1V, 14.8V.
※Installation confirmed with Tokyo Marui products. Be sure to check the installation to the overseas electric gun before purchasing. (Defectives due to installations other than Tokyo Marui are not covered by the warranty.)
※If you have already installed a barrack and a bite, remove the barrack and a bite. (Do not attach both)
※100% inspection / confirmation is performed at the time of shipment.
※There is a possibility that chattering may occur in a small part of the electric gun with a micro switch used / extremely worn out switch. Check the switch before installation.
![LayLax [Specna Arms] SA-E14 EDGE Airsoft Electric Gun [with MOSFET]](https://cdn11.bigcommerce.com/s-9mcepdq780/images/stencil/500x659/products/1823/7464/1__90432.1614905470.jpg?c=2 "LayLax [Specna Arms] SA-E14 EDGE Airsoft Electric Gun [with MOSFET]")
![LayLaxSpecna Arms] SA-E14 EDGE Airsoft Electric Gun [with MOSFET]](https://cdn11.bigcommerce.com/s-9mcepdq780/images/stencil/500x659/products/1823/7463/2__10318.1614905046.jpg?c=2 "LayLaxSpecna Arms] SA-E14 EDGE Airsoft Electric Gun [with MOSFET]")
